Electric toothbrush Oral-B Vitality 3D White D12.513W blister pack


IT IS IMPORTANT

  • Check all product/wires/accessories for damage from time to time. A damaged or non-functional part must not be used any longer. If the product, accessories or cords are damaged, contact an Oral-B service center. Do not repair or modify the product yourself. Doing so may cause fire, electric shock, or other damage.
  • Not recommended for use by children under 3 years of age. Children and persons with reduced physical, sensory or mental capabilities or lack of experience can use the device after they have been taught how to use it safely and have been advised of the hazards.
  • Cleaning and servicing of the product should not be performed by children.
  • Do not allow children to play with the device.
  • Use the product only for its intended purpose as described in this manual.
  • Do not use accessories not recommended by the manufacturer.

CAREFULLY

  • If the device is dropped, the attachment must be replaced before next use, even if there is no visible damage.
  • Do not expose the charger, plug, or travel case to water or other liquids, or place them where they could accidentally fall into a sink or bathtub. If these devices fall into water, do not remove them. Unplug them immediately.
  • Do not open or disassemble the device. To recycle the battery, please dispose of the entire device in accordance with the environmental regulations applicable in your area. Damage to the handle will damage the device and void the warranty.
  • When unplugging the device, hold it by the plug, not the cord. Do not touch the plug with wet hands, as this may cause electric shock.
  • If you are being treated for an oral condition, consult your healthcare professional before using the device.
  • This toothbrush is intended for individual use and cannot be used by multiple patients in a dental clinic or institute.
  • Replace the brush (head) every three months, or more often if it is very worn.
  • The travel case with charging function is equipped with a special power cord (smart plug) for connecting to the network, equipped with a built-in safety extra-low voltage power supply. Do not replace or disassemble its components, as this may cause electric shock. Use only the power cord that came with your device.

Important information

  • Your Oral-B toothbrush can connect to your smartphone (see Connecting your toothbrush to your smartphone for more information).
  • To avoid radio interference and/or compatibility issues, turn off the radio transmitter on the brush handle (5) before using it in restricted areas such as airplanes or designated areas in hospitals.
  • To turn off the radio transmitter, simultaneously press and hold the on/off button (3) and the mode button (4) for two seconds until the radio transmission display (7) goes out. Follow the same steps to turn the transmission back on.
  • If you use a pacemaker, do not bring the brush closer than 15 centimeters to it while it is on. If you experience interference, immediately turn off the radio transmitter in the handle.


Instructions for use


The preparatory procedure includes actions aimed at ensuring that the treatment of the oral cavity is carried out as comfortably as possible:

  • installation of the required nozzle - the rod is inserted into the groove until a characteristic click is heard;
  • during initial use, carry out testing - fill the reservoir with water and pass all of it through the device;
  • immediately before treatment , pour warm water into a container; if desired, you can mix it with mouth rinse;
  • select the appropriate mode.

Now you can start processing.

Technological manipulations according to the instructions supplied with the device:

  • all procedures must be carried out over a sink, the mouth must be kept open at all times - this way liquid will not collect in the cavity;
  • bring the irrigator into operating mode by pressing the “start” button;
  • select the desired water supply speed, taking into account that the higher it is, the stronger the jet pressure will be;
  • virtually divide the entire jaw row into 4 sectors to work with each one in turn;
  • point the nozzle head to the farthest area and turn on the liquid pressure;
  • work carefully and slowly - start with the spaces and crevices between organs, gradually moving to the dental pockets. Only after this should you rinse the remaining tooth fragments. Using this principle, process the entire jaw row.

Charging and use

Your toothbrush has a waterproof handle and is designed for safe use in the bathroom.

  • You can start using the toothbrush immediately or after a short charging period by placing it on the charging station (9). Note: if the battery is completely discharged (the charge level indicator light on the display (8) does not light up during charging, or the device does not respond to pressing the on/off button (3)), it is necessary to charge it for at least 30 minutes.
  • The charge level is displayed on the charge indicator (8). A flashing light means the brush is charging (Fig.①); Once charging is complete, the indicator light turns off. A full charge usually takes 15 hours and lasts for up to 12 days of regular toothbrush use (twice a day for two minutes) (Fig.①).
  • Note: If the device is completely discharged, the indicator light may not light up for the first 30 minutes of charging.
  • When the battery charge is low, the red indicator light on the charge level display starts flashing and the motor speed decreases. When completely discharged, the motor will stop; For single use, you will need to charge the device for at least 30 minutes.
  • You can keep the handle on the plugged-in charger at all times to maintain a full charge; The device is protected from overcharging. Note: For best performance, store the brush handle at room temperature.

Caution : Do not expose the handle to high temperatures above 50°C.

Operating modes

The model is designed taking into account the possibility of uninterrupted operation in two versions:

  1. Turbo flow - consists of multiple micro jets, which are initially given a spiral-shaped trajectory, covering a wide field of impact of the water flow. It's similar to a shower, but with more pressure. Ideal for treating pockets, prosthetic structures and disinfection;
  2. Monoflow is a pulsed flow of water supplied under pressure with a narrowly targeted spectrum of action. The pulsation is practically not noticeable. Suitable for removing plaque and food fragments.

Using your toothbrush

Teeth brushing technique

Wet the brush head and apply any toothpaste. To prevent splashing, bring the brush head close to your teeth before pressing the button on the handle (Fig.②). If you are using one of the Oral-B rotating brush heads, move it slowly from tooth to tooth, pausing on each surface for a few seconds. When using the Oral-B TriZone , place the bristles of the brush against your teeth at a slight angle to the gum line. Apply gentle pressure and begin brushing in a back-and-forth motion, similar to a manual toothbrush. Regardless of the brush head you use, start on the outside of your teeth, move to the inside, and then clean the chewing surfaces. Give equal attention to all four quadrants of the mouth.

You can also consult your dentist or oral hygienist about the technique that is best for you.

During the first few days of using any electric toothbrush, your gums may bleed a little. Usually this phenomenon stops after a few days. If bleeding gums persist for two weeks, contact your dentist or oral hygienist. If you have sensitive teeth and/or gums, Oral-B recommends using the Sensitive mode (possibly in combination with the Oral-B Sensitive brush head).

Smart Ring

Your toothbrush is equipped with Smart Ring technology, which varies depending on the color of the light: White (default) = activity indicator and visual timer (select a different color in the Oral-B™ app settings)

red = pressure sensor indicator

blue = Bluetooth® connection indicator

Timer

You can choose "Professional" or "Two Minute" mode

The “Two Minute” timer turns on a long intermittent beep and a flashing Smart Ring light (2) when two minutes have elapsed—the length of time recommended by experts for brushing your teeth.

The “Professional” timer gives a signal to move to the next quadrant of the oral cavity with a short intermittent sound signal and a flashing Smart Ring light indicator (2) (Fig. ③). A long intermittent beep and a flashing light indicate the end of the two-minute period of brushing your teeth in accordance with the recommendations of specialists.

The timer remembers the elapsed time even if the brush is turned off briefly during use. The timer is reset when there is a pause longer than 30 seconds, a short press on the mode selection button (4) during the pause, or placing the brush handle on the charger.

Note: When using special options in the Oral-B™ app, the visual timer may be deactivated.

Timer setting:

By default, your brush has the Professional timer activated. To change settings, press and hold the mode button (4) for 2 seconds. Select the timer mode with the “on/off” button (3). Confirm your choice by pressing the mode button.

  • 2 light signals - “Two-minute” mode is selected
  • 4 light signals - “Professional” mode is selected

Note: You can also set/adjust the timer through the Oral-B™ app.

Pressure meter

If you press too hard on the brush, the Smart Ring (2) lights up red, indicating the need to release the pressure. In addition, the head will stop pulsating and its rotation speed will decrease (in “Daily”, “Professional” and “Sensitive” modes) (Fig.③). Periodically check the operation of the pressure sensor by applying gentle pressure to the brush during use.

Operating modes (depending on model)

Your toothbrush offers different brushing modes. The selected mode is reflected in the mode display (6) on the brush handle (except for the “Daily Cleaning” mode):

Daily brushing ” is a standard regimen for daily oral care

Professional cleaning ” – for a feeling of unusual cleanliness (high frequency of movements)

Gentle Cleaning ” – gentle but thorough cleaning of sensitive areas

3D White ” – polish for periodic or daily use

Gum care ” – gentle gum massage

Tongue hygiene ” – cleaning the tongue for periodic or daily use

To use the Tongue Hygiene mode, we recommend using the Sensitive attachment. You can clean your tongue with or without toothpaste. Brush the entire surface of the tongue with gentle, systematic movements. The recommended time is 20 seconds, its end is indicated by a flashing Smart Ring light signal.

Your toothbrush automatically starts in the last mode you selected. To switch to another mode, press the mode button successively while using the brush (Fig.④). To return to the “Daily Cleaning” mode from any other mode, press and hold the mode selection button (4).

Note: You can also select/adjust the mode through the Oral-B™ app.

Design features


This device is a stationary type irrigator. Powered by electricity. The cleaning procedure is carried out efficiently and gently, so the device can be used by people suffering from increased tooth sensitivity.

The irrigator is equipped with a hydromassage option. Used for medicinal and health purposes. The model supplies oxygen-enriched liquid in a ratio of 95:5. The air flow enters the water jet using a special filter, which prevents microparticles of dust and foreign impurities from entering.

The water jet is supplied through the nozzle in two ways - this is very convenient. The multi-speed mode operates; they are changed by pressing the regulator located on the device body. It's simple and functional. By the way, everything in this model is designed for maximum comfort during operation.

The kit includes a reservoir; it is enough for one standard procedure.

All attachments are stored in a compact and convenient container with separate cells. The model can be mounted on a wall (a special bracket made of durable plastic is included in the kit).

For more details about the device, see the video.

Replaceable attachments

Oral-B offers you a variety of replacement attachments to fit your Oral-B handle.

Our rotating brush heads are used to precisely clean every tooth.

Oral-B CrossAction attachment

The most advanced of our attachments. Angled bristles for precise cleaning. Removes and eliminates plaque.

Oral-B FlossAction Attachment

Micropulsating bristles allow for effective plaque removal in the space between teeth

Oral-B 3D White

Special polishing cap for natural teeth whitening. Not suitable for use by children under 12 years of age.

Oral-B Sensi Ultrathin nozzle

It is a combination of regular bristles for cleaning the surface of teeth and ultra-fine bristles for cleaning areas along the gum line.

Most Oral-B brush heads are equipped with light blue INDICATOR® bristles, allowing you to keep track of when the brush head needs to be replaced. If you brush your teeth thoroughly twice a day for two minutes, the bristles will fade by half in about three months, demonstrating the need to change the brush head. If the bristles become frayed before the color has faded, you may be pressing too hard on the brush when brushing.

We do not recommend using Oral-B FlossAction or Oral-B 3D White attachments if you wear braces.

The Oral-B “Ortho” brush head is specially designed for cleaning teeth around braces and braces.

Advantages

The undeniable advantages of this model include the following:

  • high degree of cleaning compared to analogue options when removing food fragments and plaque;
  • does not injure the surface of the gums at all;
  • has an additional function (which is not found in all devices of this type) of antibacterial cleaning;
  • ease of operation;
  • excellent external aesthetics;
  • safe and environmentally friendly materials and alloys;
  • reliability and durability.

See photos of composite veneers before and after treatment. Click here to learn more about properly caring for dental implants to prolong their life.

At this address https://dr-zubov.ru/krasota-i-uxod/preparaty-i-produkty/kak-zashhitit-ot-vozdejstviya-krasyashhix.html we suggest finding out what products stain teeth and how to get rid of the problem.

Connecting a toothbrush to a smartphone

The Oral-B™ app is available for mobile devices running iOS or Android operating systems. It can be downloaded from App Store(SM) or Google Play™.

A sensor is built into the handle of the toothbrush, which, through a mobile application, determines the location of the toothbrush and helps brush your teeth. Use a smartphone holder (for more details, see the “Accessories – Smartphone Holder” section).

What's more, the Oral-B™ app allows you to track your brushing progress and create custom brush settings (see Oral-B™ app instructions for other benefits).

  • Launch the Oral-B™ app. It will help you set up a Bluetooth connection.
  • Note: The functionality of the Oral-B™ app is limited if your smartphone's Bluetooth wireless technology is disabled (refer to your smartphone's manual for connection instructions).
  • All instructions for using the application will be displayed on your smartphone.
  • If Bluetooth wireless technology is activated on the brush handle, the Bluetooth symbol on the radio transmission display (7) will light up. Once the connection is established, the Smart Ring (2) will blink once.
  • When using the brush, keep your smartphone nearby (up to 5 m). Make sure it is placed securely in a dry place.

Note: To connect to your toothbrush, your smartphone must have Bluetooth 4.0 (or higher)/Bluetooth Smart.

A list of compatible smartphones is available in the App Store(SM) or Google Play™.

Caution: Refer to your smartphone's user manual for information regarding whether the device/charger can be used in the bathroom.

For country availability of the Oral-B™ app, see www.oralbappavailability.co.uk.

Accessories

(Depending on model)

Smartphone holder

  • Before each use, make sure that the mirror to which the holder will be attached, the suction cups (11d) and the holder brackets (11a) are clean and dry (Fig. B1). Use a smooth cloth to clean the surface of the suction cups and mirror. Make sure the surface of the suction cups and mirror is clean (no dust, hair, oil, lint, dirt, etc.).
  • Gently press the smartphone holder (11) with sufficient force, attaching it approximately at nose level to the mirror. Then install the holder by pressing the lever (11b) until it clicks into place (Figure B2). Note: For proper and safe use, do not attach the holder to surfaces other than a mirror. For bathroom use only. Do not use in a car.
  • Make sure the holder is securely attached to the mirror before placing your smartphone on it. Place the smartphone in a vertical position between the holder brackets (11a), pressing alternately on one of the brackets and pushing the second one to the side (Fig. B2). To remove the smartphone, repeat the procedure.
  • Place the smartphone at the desired angle by turning the ball joint of the holder (Fig. B3).
  • After brushing your teeth, remove your smartphone from the holder. To remove the holder, release the lever and carefully pull the tab (Fig. B4 1./2). Re-attach the holder to the mirror each time you use it.
  • The smartphone holder can only be cleaned with a damp cloth (Fig.⑤). You can use glass cleaner, alcohol or similar products (avoid products with silicone oil). Make sure the surface is dry and clean. Store the holder in a clean and dry place. Do not leave your smartphone in the holder after use.

Note: Required smartphone width: no less than 58 mm, no more than 83 mm.

Caution : Small parts may break off, keep away from children.

Refer to your smartphone's manual for information on whether the device/charger can be used in the bathroom.

Travel charging module

  • To charge the toothbrush handle (5), place it on the lip of the travel charger (12) and connect it to power using the optional power cord (13).
  • The flashing indicator light (12a) of the travel charging module indicates that charging is in progress. When fully charged, the indicator turns off. A full charge takes up to 12 hours (Figure C1). Note: When the travel charger is plugged in, you can use the USB port (12b) to charge any other electronic device. The toothbrush can only be charged via the power cord (13)/(12c), but not via the USB port.
  • The internal lighting unit of the travel charging module has a built-in holder (12d) on which you can place your smartphone while using the brush (Fig. C2). Before use, make sure that the smartphone fits the dimensions of the stand and is securely fastened.
  • The removable inner layer (fig. C3) (12e) of the travel charging module can be washed in the dishwasher (fig. ⑤). The external module is cleaned with a damp cloth. Make sure the parts are completely dry before assembly and that the toothbrush/head is dry before placing it in the module.

Note: Remove stains from the surface of the module immediately. Store the module in a clean and dry place.

Refer to your smartphone's user manual for information on whether the device/charger can be used in the bathroom.

Cosmetic bag

Keep the toothbrush clean and dry in the travel case (15) in the cosmetic bag (14) (Fig. D1/2). Immediately remove stains from the surface of the brush. The cosmetic bag can only be washed by hand in warm water (30°C-40°C) (Fig. ⑤). Store in a dry, clean place.

Characteristics


Basic operational and technical characteristics of the model declared by the manufacturer:

  • type of device - for family use;
  • expected number of operating modes – 2;
  • warranty period – 24 months from the date of sale through the retail chain;
  • additional nozzles included;
  • container for storing nozzles - available;
  • functions – at least 8 thousand reciprocating rotational revolutions per minute;
  • uninterrupted operation time – 15 minutes;
  • weight – 1 kg;
  • the volume of the water tank is 600 ml, the calculated period of operation of the product is not three minutes, which is quite enough for one cleaning cycle;
  • width – 17 cm;
  • height – 15 cm;
  • depth – 13 cm;
  • the size of the jet supply tube is 1 m, which creates additional convenience during use;

The modes for adjusting the pressure of the liquid jet function autonomously and are switched using a slider mounted in the base of the nozzle, in the direction down – up.

Features of basal dental implantation and indications for the procedure. In this article, read about cbw prosthetics - what it is and what are the advantages of the technique.

Follow the link https://dr-zubov.ru/lechenie/zuby/kak-oformit-nalogovyj-vychet-vozvrashhaem-dengi-gramotno.html if you are interested in how to get a tax deduction for dental treatment.

Warranty

We [Braun] provide a two-year warranty on the product from the date of purchase.

During the warranty period, we [Braun] agree to correct, free of charge, any product defects resulting from defects in materials or workmanship by repairing or replacing the product at our option.

This warranty applies to all countries in which the device is supplied by Braun or its designated distributor. The warranty does not cover damage resulting from misuse or normal wear and tear of the product, especially with regard to attachments, or defects that have a minor effect on the operation of the device.

The product will be voided if repairs are carried out by unauthorized persons or if non-original Braun spare parts are used.

The device is equipped with an approved Bluetooth Smart radio module. Failure to establish a Bluetooth Smart connection with certain smartphone models is not covered by the warranty unless the device's Bluetooth radio module is damaged.

The warranty for Bluetooth devices is provided by the manufacturers of such devices and not by Oral-B. Oral-B does not have any influence or recommendation on the manufacturers of such devices and therefore is not responsible for the number of devices that are compatible with our Bluetooth systems.

Oral-B reserves the right, without prior notice, to make any technological modifications or changes in the system implementation of individual device elements, its interface or menu structure that it deems necessary for the proper functioning of these systems.

To carry out warranty service, hand over or send the device, complete and with a sales receipt, to an authorized Oral-B Braun Consumer Service Center.

Information

Bluetooth® radio module

Although Oral-B supports all designated Bluetooth device functions, we cannot guarantee 100% reliability of the connection and operation of the radio.

The performance and reliability of the connection directly depend on the characteristics of each specific Bluetooth device, the software version, the operating system installed on the Bluetooth device and the safety standards established by the manufacturer. Oral-B strictly adheres to the Bluetooth standard, which allows Bluetooth devices to connect and operate in conjunction with Oral-B toothbrushes.

However, if the device manufacturer does not comply with this standard, it may affect the compatibility and operation of Bluetooth devices and cause difficulties for the user. Please note that the software installed on your Bluetooth device may significantly affect connectivity and performance.

1) Warranty - exclusions and limitations

The limited warranty applies only to new products manufactured by or for The Procter & Gamble Company (“P&G”), its affiliates and subsidiaries and bearing the Braun/Oral-B brand, trademark or logo. The Limited Warranty does not apply to non-P&G products, including hardware and software. P&G is not responsible for damage to or loss of programs, data or other information stored on any media embedded in the product or for any product or part not manufactured by or for P&G and not covered by the limited warranty.

This limited warranty does not cover (i) damage caused by accident, abuse, careless or improper use or application, or damage to products not manufactured by or for P&G; (ii) damage caused by service performed by persons other than Braun and Braun-authorized service centers; (iii) products and parts modified without the written permission of P&G and (iv) damage caused by the use or inability to use the Oral-B Smartphone Stand, Smartphone Holder or Travel Case (“Accessories”),

2) Using a smartphone holder

The included Oral-B accessories allow you to conveniently position your smartphone while using the Oral-B app. Before using it for the first time, try out different positions of your smartphone in the Oral-B holder and choose the best one. Make sure that the smartphone will not fall or break. Do not use the accessory in a car.

LIMITATION OF LIABILITY

TO THE EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL P&G, ITS DISTRIBUTORS OR SUPPLIERS BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY KIND, DIRECT, INDIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, PUNITIVE DAMAGES OF ANY NATURE ARISING OUT OF USE OR INABILITY USE OF ORAL-B ACCESSORIES, INCLUDING WITHOUT LIMITATION, INJURY TO PERSON, DAMAGE TO PROPERTY, DEPRESSION OF THIRD PARTY PRODUCTS USED IN OR IN COMBINATION WITH ORAL-B ACCESSORIES, LOSS OF PERFORMANCE ORAL-B ACCESSORIES OR THIRD PARTY PRODUCTS USED IN OR IN CONJUNCTION WITH ORAL-B ACCESSORIES, INCLUDING P&G NOTIFYING THE POSSIBILITY OF SUCH AN OUTCOME. WITHOUT LIMITATION TO THE FOREGOING, YOU UNDERSTAND AND ACKNOWLEDGE THAT P&G SHALL NOT HAVE ANY RESPONSIBILITY FOR DAMAGE OR DESTRUCTION TO ANY CONSUMER ELECTRONIC DEVICES OR THIRD PARTY PROPERTY CONTAINED IN OR USED IN CONNECTION WITH ORAL ACCESSORIES. B, AS WELL AS FOR LOSS OF DATA CONTAINED IN THE MENTIONED DEVICES . IN NO EVENT SHALL ORAL-B'S REFUND EXCEED THE ACTUAL PRICE PAID FOR THE PRODUCT UPON PURCHASE.

Warranty for replacement tips

The device will be voided from Oral-B's warranty if damage to the device's electric rechargeable handle occurs as a result of using replacement attachments from another manufacturer.

  • Oral-B does not recommend the use of refills from other manufacturers.
  • Oral-B cannot control the quality of these brush heads and therefore cannot guarantee the quality of teeth cleaning they will provide, as stated upon initial purchase of the electric rechargeable handpiece.
  • Oral-B cannot guarantee the compatibility of the Oral-B Handle with refills from other manufacturers.
  • Oral-B cannot predict the long-term impact of using other brands of refills on handle wear.

All Orai-B refills have the appropriate logo and meet Oral-B's high quality standards. Oral-B does not sell refills or handpiece replacement parts under other brand names.

Caring for your device

The quality of operation and service life of the device is largely determined by the correctness of its maintenance:

  • When adding rinsing agents and refreshing compounds, rinse the container well after treatment. To do this, take a new portion of water and pass it through the unit;
  • do not leave residual water in the tank - this way you can avoid the appearance of precipitation;
  • after using the device, remove the nozzle, wash it thoroughly under running water, dry it and put it in a storage container;
  • The handle is treated with a damp cloth and wiped dry.

Trouble-shooting

ProblemPossible reasonRemedy
The brush does not work (does not work properly) with the Oral-B™ app
  1. The Oral-B™ app is turned off.
  2. The Bluetooth interface is not activated on the smartphone.
  3. The radio transmitter on the brush is turned off; The radio transmission display (7) is turned off.
  4. The Bluetooth connection between the smartphone and the brush is broken.
  5. Your smartphone does not support Bluetooth 4.0 (and higher versions)/Bluetooth Smart.
  6. The brush handle is charging.
  1. Turn on the Oral-B™ app
  2. Activate the Bluetooth interface on your smartphone (see the description in the smartphone instructions).
  3. Activate the radio transmission by pressing the on/off button (3) and the mode button (4) simultaneously for 2 seconds until the radio transmission display (7) turns on.
  4. Once again, establish a connection between the handle and the smartphone through the application settings. Keep your smartphone as close to the handle as possible during use.
  5. Your smartphone does not support Bluetooth 4.0 (and higher versions)/Bluetooth Smart. Look for a list of compatible smartphones in the App Store(SM) or Google Play™.
  6. Radio transmission stops when the handle is placed on a plugged-in charger.
Resetting settings to factory defaults Requires original mobile app functionalityPress and hold the on/off button (3) for 10 seconds until all indicator lights turn on twice simultaneously.
The brush does not work (on first use) Low battery level; no light indication. Charge for at least half an hour.
The brush does not work with SmartGuide.
  1. Unsuccessful synchronization with SmartGuide.
  2. The radio transmitter is turned off; The radio transmission display (7) is turned off.
  3. SmartGuide is not brush compatible.
  4. Two brushes are associated with SmartGuide at the same time.
  5. Feature disabled via Oral-B™ app.
  1. Sync the (existing) brushes (again) using the SmartGuide settings under Battery Charge in SmartGuide: hold "h/min" for 3 seconds. Turn on the brush you want to sync. Then turn on the second brush you want to sync. Press "h/min" or "set" to exit timing mode.
  2. Activate the radio transmission by simultaneously pressing the on/off buttons (3) and the mode button (4) for 2 seconds until the radio transmission display turns on.
  3. The brush cannot be used with the SmartGuide connected.
  4. You can synchronize just 2 brushes. Change brushes using SmartGuide settings (see 1)
  5. When using special functions of the application, transmission to SmartGuide may be deactivated. You can also deactivate any SmartGuide communication using the app.
  1. Short intermittent beep/flashing light every 30 seconds or after two minutes of brush use.
  2. The timer does not work.
  1. The “Professional” or “2-minute” timer is activated.
  2. The timer has been modified/disabled via the Oral-B™ app.
  1. Set the "2 Minute" timer (intermittent sound/flashing light after 2 minutes); or set the “Professional” timer (intermittent sound/flashing light every 30 seconds). Proceed according to “Setting the timer”.
  2. Use the app to change the timer settings or perform a factory reset (see Possible problems in the app).
The brush does not dress up
  1. Battery power is very low.
  2. The ambient temperature is not within the range suitable for charging (below 0°C or above 60°C).
The charge indicator may not start flashing immediately, but may take up to 30 minutes.

The recommended ambient temperature for charging the battery is from 5 °C to 35 °C.

This electric toothbrush is equipped with a Bluetooth radio module operating in the 2.4-2.48 GHz range with a maximum power of 1 mW.

Braun GmbH therefore declares that radio equipment types 3765, 3754, 3764,3762 and 3767 comply with the requirements of EU Directive 2014/53/EU. The full text of the European Declaration of Conformity is available for review on the following Internet page: https://www.oralb.com/ce

Made in Germany

Production date code:

To determine the year and month of manufacture, look at the manufacture code located on the charger or handle plate. Find a code (minimum 11 characters) starting with a letter.

Charger: The first digit of the code indicates the year of manufacture. The next two digits indicate the calendar week of the year of production.

For example: "509" means that the product was produced in the 9th week of 2015. Handle: The first digit of the production code indicates the year of production. The next two digits indicate the month of production.

For example: "509" means that the product was produced in September 2015.

Manufactured in Germany for Braun GmbH, Frankfurter Strasse 145, 61476 Kronberg, Germany/Braun GmbH, Frankfurter Strasse 145, 61476 Kronberg, Germany

RU Importer/Consumer Service: Procter and Gamble Distribution Company LLC, Russia, 125171, Moscow, Leningradskoe Shosse, 16A, building 2. Tel. 8-800-200-20-20

BY Suppliers to the Republic of Belarus: LLC "Electroservice and Co", Belarus, 220012, Minsk, st. Chernyshevsky, 10A, room 412AZ., IOO "ALIDI-West", 220140, Belarus, Minsk, st. Dombrovskaya, 9, of. 7.3.1. Service, Belarus, 220012, Minsk, st. Chernyshevsky, 10A, room 115 B

Warranty period/Service life: 2 years.

E.A.C.

Electric toothbrush type 3765 with charger type 3757, with portable charger type 3760 and mains adapter type 492-5214

220-240 Volts, 50-60 Hertz, 0.9 Watt

Electric shock protection class: II

Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]